## CentreCOM AR300/AR700 シリーズ 設定例集 2.3
##  102 L2TP＋IPsecによるLAN間接続（IP/IPX。両側アドレス固定。インターネットアクセスあり）
##  ルーターBのコンフィグ
##
## 「#」で始まる行は、コンソールから入力しないと意味を持たないコマンドです。

ADD USER=secoff PASSWORD=PasswordS PRIVILEGE=SECURITYOFFICER
SET BRI=0 MODE=TDM ACTIVATION=ALWAYS TDMSLOTS=1-2
CREATE TDM GROUP=ISPB INT=bri0 SLOTS=1-2
CREATE PPP=0 OVER=TDM-ISPB LQR=OFF
ENABLE IP
ADD IP INT=eth0-0 IP=200.100.20.1 MASK=255.255.255.240
ADD IP INT=eth0-1 IP=192.168.20.1 MASK=255.255.255.0
ADD IP INT=ppp0 IP=0.0.0.0
ADD IP ROUTE=0.0.0.0 INT=ppp0 NEXT=0.0.0.0
ENABLE L2TP
ENABLE L2TP SERVER=BOTH
ADD L2TP CALL=remote IP=200.100.10.1 TYPE=VIRTUAL REMOTE=remote PRECEDENCE=IN
CREATE PPP=1 OVER=TNL-remote IDLE=ON BAP=OFF LQR=OFF
ADD IP INT=ppp1 IP=0.0.0.0
ADD IP ROUTE=192.168.10.0 MASK=255.255.255.0 INT=ppp1 NEXT=0.0.0.0
ENABLE IPX
ADD IPX CIRCUIT=1 INTERFACE=eth0 NETWORK=12 ENCAPSULATION=802.3
ADD IPX CIRCUIT=2 INTERFACE=ppp1 NETWORK=129 DEMAND=ON
ADD IPX ROUTE=401 CIRCUIT=2 NEXTHOP=129:0000f4740012
ADD IPX ROUTE=7500 CIRCUIT=2 NEXTHOP=129:0000f4740012
ADD IPX SERVICE=Accounts ADDRESS=7500:00000001:0451 TYPE=file CIRCUIT=2 HOPS=2
ENABLE FIREWALL
CREATE FIREWALL POLICY=net
ENABLE FIREWALL POLICY=net ICMP_F=PING,UNREACH
DISABLE FIREWALL POLICY=net IDENTPROXY
ADD FIREWALL POLICY=net INT=eth0-0 TYPE=PRIVATE
ADD FIREWALL POLICY=net INT=eth0-1 TYPE=PRIVATE
ADD FIREWALL POLICY=net INT=ppp0 TYPE=PUBLIC
ADD FIREWALL POLICY=net INT=ppp1 TYPE=PRIVATE
ADD FIREWALL POLICY=net NAT=ENHANCED INT=eth0-1 GBLINT=ppp0 GBLIP=200.100.20.1
ADD FIREWALL POLICY=net RU=1 AC=ALLOW INT=ppp0 PROT=UDP GBLPO=500 GBLIP=200.100.20.1 PO=500 IP=200.100.20.1
ADD FIREWALL POLICY=net RU=2 AC=NONAT INT=eth0-1 PROT=ALL IP=192.168.20.1-192.168.20.254
SET FIREWALL POLICY=net RU=2 REMOTEIP=192.168.10.1-192.168.10.254
ADD FIREWALL POLICY=net RU=3 AC=NONAT INT=ppp0 PROT=UDP PORT=1701 IP=200.100.20.1 ENCAP=IPSEC
# CREATE ENCO KEY=1 TYPE=GENERAL VALUE="secret"
CREATE ISAKMP POLICY="i" PEER=200.100.10.1 KEY=1 SENDN=TRUE
CREATE IPSEC SASPEC=1 KEYMAN=ISAKMP PROTOCOL=ESP ENCALG=DES HASHALG=SHA MODE=TRANSPORT
CREATE IPSEC BUNDLE=1 KEYMAN=ISAKMP STRING="1"
CREATE IPSEC POLICY="isa" INT=ppp0 ACTION=PERMIT LPORT=500 RPORT=500 TRANSPORT=UDP
CREATE IPSEC POLICY="L2" INT=ppp0 ACTION=IPSEC KEYMAN=ISAKMP BUNDLE=1 PEER=200.100.10.1
SET IPSEC POLICY="L2" LAD=200.100.20.1 LPORT=1701 RAD=200.100.10.1 RPORT=1701 TRANSPORT=UDP
CREATE IPSEC POLICY="inet" INT=ppp0 ACTION=PERMIT
ENABLE IPSEC
ENABLE ISAKMP
# LOGIN secoff
# ENABLE SYSTEM SECURITY_MODE