## CentreCOM AR300/AR700 シリーズ 設定例集 2.3
##  114 PPPoEインターネット接続環境におけるL2TP＋IPsec LAN間接続（IP/AppleTalk。両側アドレス固定）
##  ルーターAのコンフィグ
##
## 「#」で始まる行は、コンソールから入力しないと意味を持たないコマンドです。

ADD USER=secoff PASSWORD=PasswordS PRIVILEGE=SECURITYOFFICER
CREATE PPP=0 OVER=eth1-any
SET PPP=0 OVER=eth1-any BAP=OFF IPREQUEST=ON USER=user@ispA PASSWORD=isppasswdA LQR=OFF ECHO=ON
ENABLE IP
ENABLE IP REMOTEASSIGN
ADD IP INT=eth0-0 IP=4.4.4.2 MASK=255.255.255.248
ADD IP INT=eth0-1 IP=192.168.10.1 MASK=255.255.255.0
ADD IP INT=ppp0-0 IP=0.0.0.0
ADD IP INT=ppp0-1 IP=4.4.4.1 MASK=255.255.255.255
ADD IP ROUTE=0.0.0.0 INT=ppp0-1 NEXTHOP=0.0.0.0
ENABLE TRIGGER
CREATE TRIGGER=1 PERIODIC=3 SCRIPT=reset.scp
CREATE TRIGGER=2 INTERFACE=ppp0 EVENT=UP CP=IPCP SCRIPT=up.scp
CREATE TRIGGER=3 INTERFACE=ppp0 EVENT=DOWN CP=IPCP SCRIPT=down.scp
ENABLE L2TP
ENABLE L2TP SERVER=BOTH
SET L2TP PASSWORD=l2tpA
ADD L2TP CALL=remote IP=12.34.56.78 TYPE=VIRTUAL REMOTE=remote PRECEDENCE=OUT PASSWORD=l2tpB
CREATE PPP=1 OVER=TNL-remote IDLE=ON BAP=OFF LQR=OFF
ADD IP INT=ppp1 IP=0.0.0.0
ADD IP ROUTE=192.168.20.0 MASK=255.255.255.0 INT=ppp1 NEXT=0.0.0.0
ENABLE APPLETALK
ADD APPLETALK PORT INT=eth0 SEED=10
ADD APPLETALK ZONE=NetA PORT=1 DEFAULT
ADD APPLETALK PORT INT=ppp1 DEMAND=ON
ADD APPLETALK ROUTE=20 PORT=2 HOPS=2
ENABLE FIREWALL
CREATE FIREWALL POLICY=net
ENABLE FIREWALL POLICY=net ICMP_F=PING,UNREACH
DISABLE FIREWALL POLICY=net IDENTPROXY
ADD FIREWALL POLICY=net INT=eth0-1 TYPE=PRIVATE
ADD FIREWALL POLICY=net INT=eth0-0 TYPE=PRIVATE
ADD FIREWALL POLICY=net INT=ppp0-0 TYPE=PUBLIC
ADD FIREWALL POLICY=net INT=ppp0-1 TYPE=PUBLIC
ADD FIREWALL POLICY=net INT=ppp1 TYPE=PRIVATE
ADD FIREWALL POLICY=net NAT=ENHANCED INT=eth0-1 GBLINT=ppp0-1 GBLIP=4.4.4.1
ADD FIREWALL POLICY=net RULE=1 AC=ALLOW INT=ppp0-0 PROTO=TCP IP=4.4.4.3 PORT=80
ADD FIREWALL POLICY=net RULE=2 AC=ALLOW INT=ppp0-0 PROTO=TCP IP=4.4.4.4 PORT=25
ADD FIREWALL POLICY=net RULE=3 AC=ALLOW INT=ppp0-0 PROTO=TCP IP=4.4.4.4 PORT=53
ADD FIREWALL POLICY=net RULE=4 AC=ALLOW INT=ppp0-0 PROTO=UDP IP=4.4.4.4 PORT=53
ADD FIREWALL POLICY=net RULE=5 AC=ALLOW INT=ppp0-1 PROT=UDP GBLPO=500 GBLIP=4.4.4.1 PO=500 IP=4.4.4.1
ADD FIREWALL POLICY=net RULE=6 AC=NONAT INT=eth0-1 PROT=ALL IP=192.168.10.1-192.168.10.254
SET FIREWALL POLICY=net RULE=6 REMOTEIP=192.168.20.1-192.168.20.254
ADD FIREWALL POLICY=net RULE=7 AC=NONAT INT=ppp0-1 PROT=UDP PORT=1701 IP=4.4.4.1 ENCAP=IPSEC
# CREATE ENCO KEY=1 TYPE=GENERAL VALUE="secret"
CREATE ISAKMP POLICY="i" PEER=12.34.56.78 KEY=1 SENDN=TRUE
CREATE IPSEC SASPEC=1 KEYMAN=ISAKMP PROTOCOL=ESP ENCALG=DES HASHALG=SHA MODE=TRANSPORT
CREATE IPSEC BUNDLE=1 KEYMAN=ISAKMP STRING="1"
CREATE IPSEC POLICY="isa" INT=ppp0-1 ACTION=PERMIT LPORT=500 RPORT=500 TRANSPORT=UDP
CREATE IPSEC POLICY="L2" INT=ppp0-1 ACTION=IPSEC KEYMAN=ISAKMP BUNDLE=1 PEER=12.34.56.78
SET IPSEC POLICY="L2" LAD=4.4.4.1 LPORT=1701 RAD=12.34.56.78 RPORT=1701 TRANSPORT=UDP
CREATE IPSEC POLICY="inet" INT=ppp0-1 ACTION=PERMIT
ENABLE IPSEC
ENABLE ISAKMP
# LOGIN secoff
# ENABLE SYSTEM SECURITY_MODE