[index] CentreCOM x930シリーズ コマンドリファレンス 5.5.0
モード: インターフェースモード
カテゴリー: インターフェース / 一般設定
(config-if)# speed {10|100|1000|10000|40000|auto [10 & 100 & 1000 & 10000]}
(config-if)# no speed
対象インターフェースの通信速度を変更する。
no形式で実行した場合は初期値に戻る。
10 |
10Mbps | ||||
100 |
100Mbps | ||||
1000 |
1000Mbps(1Gbps) | ||||
10000 |
10000Mbps(10Gbps) | ||||
40000 |
40000Mbps(40Gbps) | ||||
auto [10 & 100 & 1000 & 10000] |
オートネゴシエーションで決定(初期値)。autoキーワードの後に使用可能な速度を列挙することで、オートネゴシエーションで接続可能な通信速度を制限することもできる |
■ スイッチポート1.0.1の通信モードを100M Full Duplex固定に設定する。
awplus(config)# interface port1.0.1 ↓ awplus(config-if)# speed 100 ↓ awplus(config-if)# duplex full ↓
awplus(config)# interface port1.0.2 ↓ awplus(config-if)# speed auto 10 100 ↓
■ 本コマンドは物理インターフェース(スイッチポートとマネージメント用Ethernetポート(eth0))でのみ有効。
■ インターフェースの種類に応じたspeedコマンドとduplexコマンドの有効な組み合わせは以下のとおり(「x/y」の表記はspeedコマンド/duplexコマンドの指定値を表す)。これ以外の組み合わせはサポート対象外。
マネージメント用Ethernetポート | eth0 | auto/auto(初期値), 10/half, 10/full, 100/half, 100/full, 1000/full |
1000BASE-Tポート | 固定 | auto/auto(初期値), 10/full, 100/full, 1000/full ※オートネゴシエーション時は Full Duplex のみサポート |
1000Mbps光ポート | SFP/SFP+スロット | auto/auto(初期値), 1000/full |
10GBASE-Tポート | SFP/SFP+スロット | auto/auto(初期値), 1000/full, 10000/full ※オートネゴシエーション時は1000M/10000M Full Duplexのみサポート |
AT-x9EM/XT4 | auto/auto(初期値), 1000/full, 10000/full | |
10Gbps光ポート | SFP/SFP+スロット | auto/auto(初期値), 10000/full |
QSFP+スロット 10G×4モード | auto/auto(初期値), 10000/full | |
40Gbps光ポート | QSFP+スロット | auto/auto(初期値), 40000/full |
100Mbps光ポート | コンボ | auto/auto(初期値), 100/full |
1000BASE-Tポート | auto/auto(初期値), 10/full, 100/full, 1000/full ※オートネゴシエーション時は Full Duplex のみサポート |
|
1000Mbps光ポート | auto/auto(初期値), 1000/full |
interface (グローバルコンフィグモード) | +- speed(インターフェースモード)
duplex(インターフェースモード)
polarity(インターフェースモード)
show interface(非特権EXECモード)
show interface status(非特権EXECモード)
(C) 2015 - 2020 アライドテレシスホールディングス株式会社
PN: 613-002105 Rev.AE